Steelcraft-automotive 220110 3 ROUND SIDE BAR Bedienungsanleitung PDF herunterladen

PARTS LIST:

1 Driver/Left Sidebar 4 ½” ID x 1 3/8” OD x 3/32” Flat Washers

1 Passenger/Right Sidebar 6 10-1.50mm x 25mm Hex Head Bolts

1 Driver/Left Front Mounting Bracket 12 10mm ID x 21mm OD x 1.5mm Flat Washers

1 Passenger/Right Front Mounting Bracket 6 10mm Nylock Nuts

1 Driver/Left Rear Mounting Bracket 2 12-1.75mm x 90mm Hex Head Bolts

1 Passenger/Right Rear Mounting Bracket 4 12mm ID x 29mm OD x 3mm Flat Washers

2 Front Support Brackets 2 12mm Nylock Nuts

1 Driver/Left Rear Support Bracket 2 8-1.25mm x 25mm Hex Head Bolts

1 Passenger/Right Rear Support Bracket 2 8mm Nylock Nuts

4 ½” x 2” Hex Bolts 4 8mm ID x 22mm OD x 1.5mm Flat Washers

4 ½” Lock Washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

2. Remove the passenger front body mount bolt. Locate passenger side front Mounting Bracket and

partially hang it to body mount using the factory bolt (Figure 1).

3. Locate (1) Front Support Bracket and attach it to already installed front Mounting Bracket using (2)

10mm x 25mm Hex Head Bolts, (2) 10mm Nylock Nuts, and (4) 10mm Flat Washers (Figure 2).

Attach opposite side of Support Bracket to smaller factory hole in the frame using (1) 12mm x

90mm Hex Head Bolt, (1) 12mm Nylock Nuts, (2) 12mm Flat Washers (Figure 4 & 5). Do not

tighten at this time.

4. Remove the passenger rear body mount bolt. Locate passenger side rear Mounting Bracket and

partially hang it to body mount using the factory bolt (Figure 6).

5. Locate (1) Rear Support Bracket and attach it to already installed rear Mounting Bracket using the

included (1) 10mm x 25mm Hex Head Bolts, (1) 10mm Nylock Nuts, and (2) 10mm Flat Washers.

Attach opposite side of Support Bracket to the factory hole on the inner side of body mount cavity

and closer to the frame using (1) 8mm x 25mm Hex Head Bolt, (1) 8mm Nylock Nut, and (2) 8mm

Flat Washers (Figure 7). Do not tighten at this time.

6. Position passenger Sidebar onto Mounting Brackets. Align holes on the Mounting Brackets with

holes on the Sidebar. Secure Sidebar to Mounting Brackets using (2) ½” x 2” Hex Head Bolts, (2)

½” Lock Washers, and (2) 12mm Flat Washers (Figure 5 & 9). Do not tighten at this time.

7. Level and align Sidebar; then tighten all hardware at this time.

8. Repeat steps 2-7 for driver Sidebar.

9. Do periodic inspections to the installation to make sure all hardware is secure and tight.

Page 1 of 4 5/30/07

(AM)

INSTALLATION INSTRUCTIONS

SIDEBAR

05-7 DODGE DAKOTA CLUB CAB

PART NUMBER

Passenger Side Brackets Driver Side Brackets

Front Front

1 2 3 4

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTIONS

PARTS LIST:1 Driver/Left Sidebar 4 ½” ID x 1 3/8” OD x 3/32” Flat Washers1 Passenger/Right Sidebar 6 10-1.50mm x 25mm Hex Head Bolts1 Driver/Le

Seite 2 - Figure 4 Figure 5

(Passenger Side Front Mounting Bracket Installation Shown) Page 2 of 4 5/30/07 (AM)Factory Bolt10mm x 25mm

Seite 3 - Figure 8

(Passenger Side Rear Mounting Bracket Installation Shown) Page 3 of 4 5/30/07 (AM)Factory Bolt10mm x 25mm

Seite 4 - Figure 9 Figure 10

Page 4 of 4 5/30/07 (AM)Figure 9 Figure 10

Kommentare zu diesen Handbüchern

Keine Kommentare

Steelcraft-automotive 220110 3 ROUND SIDE BAR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Steelcraft-automotive 220110 3 ROUND SIDE BAR herunter. Steelcraft Automotive 220110 3 ROUND SIDE BAR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Steelcraft-automotive 220110 3 ROUND SIDE BAR