Steelcraft-automotive 55100 GRILL GUARD Bedienungsanleitung PDF herunterladen

PARTS LIST:

1 Grille Guard 2 10-1.50mm x 30mm Hex Head Bolts

1 Passenger Side Mounting Bracket (A) 8 10mm Thick Flat Washers

1 Driver Side Mounting Bracket (D) 4 10mm Nylock Nuts

1 Passenger Side Top Bracket (B) 2 10mm Nut Plates

1 Driver Side Top Bracket (C) 2 10-1.50mm x 40mm Hex Head Bolts

2 8-1.25mm x 25mm Hex Head Bolts 4 12-1.75mm x 30mm Hex Head Bolts

4 8mm ID x 22mm OD x 3mm Flat Washers 8 12mm Thick Flat Washers

2 8mm Nylock Nut 4 12mm Nylock Nuts

2 10-1.50mm x 25mm Allen Bolts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY.

2. Using a flat screwdriver carefully remove all fasteners from factory plastic shroud on top and underneath the

vehicle. On the bottom there are (4) on the front and (3) on each side by the fender. On the top there are (7)

fasteners.

3. Remove bottom plastic shroud and place it on a working area. Using a hack saw carefully cut the marked

area shown in Figure 1.

4. Re-install the bottom factory plastic shroud with original fasteners. NOTE: Do not install the two fasteners

shown in Figure 1.

5. Slide Passenger Side Mounting Bracket through the previously cut out slot on the plastic shroud and

position bracket to its mounting location (Figure 2). NOTE: Rear hole on the Mounting Brackets should line

up with the holes on the plastic shroud as well.

6. Install the rear of the Passenger Side Mounting Bracket to existing hole on the sub-frame with the included

(1) 10-1.50mm x 30mm Hex Head Bolt, (1) 10mm Nylock Nut, and (2) 10mm Flat Washers(Figure 2). Do not

tighten hardware at this time.

7. Install the front of the Passenger Side Mounting Bracket to the existing hole on the factory bumper with the

included (1) 10-1.50mm x 40mm Hex Head Bolt, (1) 10mm Flat Washer, and (1) 10mm Nut Plate (Figure 2).

Do not tighten hardware at this time. IMPORTANT: Before you thread Bolt into Nut Plate, make sure

you measure the bolt. The bolt should measure no more than 40mm / 1 9/16”. If the bolt is longer

than 40mm / 1 9/16”, contact your local retailer. Do not attempt to install the bolt if it is longer than

40mm / 1 9/16”, doing so will cause damage the radiator.

8. Repeat steps 5-7 for driver side Mounting Bracket.

9. Locate the passenger side Top Bracket and slide it through top section of factory grille shell.

10. Install the inner side on the Top Bracket to the existing hole on the radiator support with the included (1)

8-1.25mm x 25mm Hex Head Bolt, (1) 8mm Nylock Nut, and (2) 8mm Flat Washers (Figure 3 & 4). Do not

tighten hardware at this time.

11. Repeat step 9 &10 for Driver Side Top Bracket.

12. With help position Grille Guard on the inner side of the Mounting Brackets. Attach Grille Guard to Mounting

Brackets with the included (4) 12-1.75mm x 30mm Hex Head Bolts, (4) 12mm Nylock Nuts, and (8) 12mm

Flat Washers (Figure 2). Do not tighten hardware at this time.

Page 1 of 2

2/22/07 (AM)

INSTALLATION INSTRUCTIONS

GRILLE GUARD

07 HONDA CRV

PART NUMBER

(A)

(B)

(C)

(D)

1 2 3

2/22/07 (AM) 2
Figure 3 Figure 4 3

Inhaltsverzeichnis

Seite 1

PARTS LIST:1 Grille Guard 2 10-1.50mm x 30mm Hex Head Bolts1 Passenger Side Mounting Bracket (A) 8 10mm Thick Flat Washers1 Driver Side Mountin

Seite 2 - 2/22/07 (AM)

(1) 10mm x 30mm Bolt, (2) 10mm Washers, & (1) 10mm Nylock Nut(1) 10mm x 40mm Bolt, (1) 10mm Washers, & (1) 10mm Nut PlatePassenger Side Shown(

Seite 3 - Figure 3 Figure 4

Figure 3 Figure 4 Page 1 of 2 2/22/07 (AM)

Kommentare zu diesen Handbüchern

Keine Kommentare

Steelcraft-automotive 55100 GRILL GUARD Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Steelcraft-automotive 55100 GRILL GUARD herunter. Steelcraft Automotive 55100 GRILL GUARD User Manual [en] [es] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Steelcraft-automotive 55100 GRILL GUARD