Steelcraft-automotive 221600 3 ROUND SIDE BAR Bedienungsanleitung PDF herunterladen

SIDEBAR

06-11 JEEP COMMANDER

7-PASSENGER W/REAR A/C ONLY

Page 1 of 4 3/22/11 Rev1(DP)

PARTS LIST:

Driver/Left Sidebar

1/2” x 2” Hex Bolts

Passenger/Right Sidebar

1/2” Lock Washers

Driver/Left Front Mounting Bracket

1/2” ID x 1-1/2” OD x 1/8” Flat Washers

Passenger/Right Front Mounting Bracket

10-1.50mm x 25mm Hex Bolts

Driver/Left Rear Mounting Bracket

10-1.50mm x 30mm Hex Bolts

Passenger/Right Rear Mounting Bracket

10mm Lock Washers

Welded Double Nut Plate

10mm ID x 30mm OD x 2.5mm Flat Washers

Welded Single Nut Plate

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. DO NOT ATTEMPT INSTALLATION ALONE;

PERSONAL INJURY OR DAMAGE TO THE VEHICLE MAY RESULT.

2. Start installation toward the driver side front-side of the vehicle. Locate the driver side-front mounting

location, (Figure 1A). Select (1) Welded Double Nut Plate, (Figure 1B). Insert the Nut Plate into the

large round hole in the floor panel. Line up the (2) threaded nuts in the Nut Plate with the large round

hole and the oval hole in the floor panel. Select the driver side Front Bracket. Hang the Bracket from

the Double Nut Plate with (2) 10mm x 30mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat

Washers inserted through the Bracket and into the Double Nut Plate, (Figure 2). Do not tighten

hardware at this time.

3. Next, move toward the driver side rear of the vehicle. Locate the factory mount for the rear trailing arm,

(Figure 3A). Select (1) Single Welded Nut Plate, (Figure 3B). Insert the flat end of the Nut Plate with

the threaded holes, (No welded nut), up and into the underside of the trailing arm mount. Line up the

threaded holes in the Nut Plate with the (2) holes in the trailing arm mount. NOTE: Make sure that the

end on the Nut Plate with the welded-on nut is towards the bottom of the trailing arm mount.

4. Select the Driver Side Rear Mounting Bracket. Insert (1) 1/2” x 2” Hex Bolt, (1) 1/2” Lock Washer and

(1) 1/2” Flat Washer out through the mounting slot in the Bracket, (Figure 4). NOTE: The 1/2" Hex Bolt

and Washers must be installed in the Bracket before it is bolted onto the car. There is very little room

between the trailing arm mount and the Bracket once the Bracket has been bolted to the vehicle.

5. Hold the Nut Plate up in position inside the trailing arm mount and hold the driver side rear Mounting

Bracket in position over the mount. Hang the Bracket from the Nut Plate by inserting (1) 10mm x 25mm

Hex Bolt, (1) 10mm Lock Washer and (1) 10mm Flat Washer through the top hole in the Bracket and

Driver/Left Front

Mounting Bracket

Driver/Left Rear

Mounting Bracket

10mm Welded Double

Nut Plate

(2) 10mm Single Welded Nut Plates

Passenger/Right Front

Mounting Bracket

Passenger/Right Rear

Mounting Bracket

1 2 3 4

Inhaltsverzeichnis

Seite 1

SIDEBAR 06-11 JEEP COMMANDER 7-PASSENGER W/REAR A/C ONLY Page 1 of 4 3/22/11 Rev1(DP) PARTS LIST: 1 Driver/Left Sidebar 4 1/2” x 2” Hex Bolts

Seite 2

SIDEBAR 06-11 JEEP COMMANDER 7-PASSENGER W/REAR A/C ONLY Page 2 of 4 3/22/11 Rev1(DP) into the threaded end of the Nut Plate, (Figure 4). NOTE: Do n

Seite 3 - 7-PASSENGER W/REAR A/C ONLY

SIDEBAR 06-11 JEEP COMMANDER 7-PASSENGER W/REAR A/C ONLY Page 3 of 4 3/22/11 Rev1(DP) Line up flat end of Nut Plate with top hole Line up end with w

Seite 4

SIDEBAR 06-11 JEEP COMMANDER 7-PASSENGER W/REAR A/C ONLY Page 4 of 4 3/22/11 Rev1(DP) Fig 6 10mm x 30mm Hex Bolt 10mm Lock Washer

Kommentare zu diesen Handbüchern

Keine Kommentare

Steelcraft-automotive 221600 3 ROUND SIDE BAR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Steelcraft-automotive 221600 3 ROUND SIDE BAR herunter. Steelcraft Automotive 221600 3 ROUND SIDE BAR User Manual [es] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Steelcraft-automotive 221600 3 ROUND SIDE BAR