Steelcraft-automotive 412459p 5 PREMIUM OVAL SIDE BAR Bedienungsanleitung PDF herunterladen

5IN BENT END SIDEBAR

99-12 FORD F-250/450 SUPERDUTY SUPER CAB

Page 1 of 2 1/5/12 (DP)

PARTS LIST:

Driver/Left Sidebar

Passenger/Right Sidebar

Driver/Left Mounting Brackets

Passenger/Right Mounting Brackets

8mm Clip Nuts

8-1.25mm x 30mm Hex Bolts

8-1.25mm x 25mm Hex Bolts

8mm ID x 24mm OD x 2mm Flat Washers

8mm Lock Washers

8mm Hex Nuts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting on the driver side-front of the vehicle, locate the 2nd set of factory holes in the body panel and

pinch weld directly under the center of the front door. Each mounting location comprises of a

rectangular hole with a round hole on each side and two holes through the pinch weld, (Figures 1 & 2).

3. Select (2) 8mm Clip Nuts. Insert Clip Nuts one at a time into the rectangular opening and slide the

threaded hole outward towards the round hole. Line up the threaded hole in the Clip with the round hole

next to the rectangular opening. NOTE: Threaded nut must go towards the inside of the side panel,

(Figures 1 & 2).

4. Partially attach the passenger side front Mounting Bracket to the Clip Nuts using the included (2) 8mm

x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 3). NOTE: Cradles on

the Mounting Brackets should face the front of the vehicle.

5. Bolt the (2) bottom holes in the Mounting Bracket to the (2) holes in the pinch weld using the included

(2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers, (4) 8mm Flat Washers and (2) 8mm Hex Nuts,

(Figure 3). Do not tighten hardware at this time.

6. Repeat Steps 2 – 5 for rear Mounting Bracket installation. NOTE: If you re not sure which sets of

mounting holes to use, (last set along cab), hold the driver Sidebar up in the approximate location and

line up the threaded inserts on the Sidebar with the holes in the pinch weld to determine the correct

mounting location.

7. Carefully unwrap and position the Sidebar onto the (2) Mounting Brackets. Bolt the Sidebar to the

Brackets with (4) 8mm x 25mm Hex Bolts, (4) 8mm Lock Washers, and (4) 8mm Flat Washers,

(Figures 3 & 4). Do not tighten at this time.

8. Level and adjust Sidebar properly and tighten all hardware.

9. Repeat Steps 2 – 8 for passenger Sidebar installation.

(2) Passenger/Right

Mounting Brackets

(2) Driver/Left

Mounting Brackets

Complete Installation

Driver/Left Sidebar illustrated

Front

1 2

Inhaltsverzeichnis

Seite 1

5IN BENT END SIDEBAR 99-12 FORD F-250/450 SUPERDUTY SUPER CAB Page 1 of 2 1/5/12 (DP)

Seite 2

5IN BENT END SIDEBAR 99-12 FORD F-250/450 SUPERDUTY SUPER CAB Page 2 of 2 1/5/12 (DP)

Kommentare zu diesen Handbüchern

Keine Kommentare

Steelcraft-automotive 412459p 5 PREMIUM OVAL SIDE BAR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Steelcraft-automotive 412459p 5 PREMIUM OVAL SIDE BAR herunter. Steelcraft Automotive 412459p 5 PREMIUM OVAL SIDE BAR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Steelcraft-automotive 412459p 5 PREMIUM OVAL SIDE BAR