Steelcraft-automotive 422509p 5 PREMIUM OVAL SIDE BAR Bedienungsanleitung PDF herunterladen

5" OVAL BENT END SIDEBARS

09-12 DODGE RAM 1500 CREW CAB

10-12 DODGE RAM 25-3500 CREW CAB

EXCLUDES VEHICLES EQUIPPED WITH DIESEL EXHAUST FLUID SYSTEMS

Page 1 of 3 12/16/11 (DP)

PARTS LIST:

Qty

Description

Qty

Description

Driver/Left Sidebar

12mm Lock Washers

Passenger/Right Sidebar

12mm Hex Nuts

Driver/Left Front and Center Mounting Brackets

10-1.5mm x 35mm Hex Bolts

Driver/Left Rear Mounting Bracket

10mm x 27mm OD x 3mm Flat Washers

Passenger/Right Front and Center Mounting Brackets

10mm Lock Washers

Passenger/Right Rear Mounting Brackets

8-1.25 x 25mm Hex Bolts

12mm Plastic Retainers

8mm x 24mm x 2mm Flat Washers

12mm x 40mm Bolt x 10mm Nut Plates

8mm Lock Washers

12mm x 32mm OD x 3mm Flat Washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting at the driver side-front of the vehicle, remove the sealing tape covering the factory

holes on the side of the inner panel, (Figure 1A, 1B, 1C). Partially thread (1) 12mm Plastic

Retainer onto the threaded end of (1) 12mm Bolt and Nut Plate, (Figure 2A). Insert the Bolt

and Nut Plate into the factory oval hole. Continue to thread the Plastic Retainer down the Bolt

and Nut Plate until it is flush against the sheet metal, (Figure 2B). NOTE: When properly

installed, the Plastic Retainer is designed to prevent the Bolt and Nut Plate from falling into the

body cavity during installation.

3. Select the driver side front Mounting Bracket and partially hang it from the Bolt and Nut Plate

with (1) 12mm Flat Washer, (1) 12mm Lock Washer and (1) 12mm Hex Nut. Do not tighten

hardware at this time. Line up the remaining hole in the Mounting Bracket with the hole in the

inner body panel. Rotate the Bolt and Nut Plate until the threaded end (Nut) lines up with the

hole in the Mounting Bracket. Secure with (1) 10mm x 35mm Hex Bolt, (1) 10mm Lock Washer

and (1) 10mm Flat Washer, (Figures 3A, 3B, 3C). Snug but do not tighten hardware at this

time.

4. Repeat Steps 2 - 3 for the center and rear Mounting Bracket installation. NOTE: The rear

Mounting Brackets, (Figure 3C), are slightly different from the front and center brackets, (see

illustration above-note bolt pattern on mounting plate).

5. Once all of the driver side Brackets have been installed, carefully position the driver Sidebar

onto the (3) Mounting Brackets. Attach the Sidebar to the cradles on the Mounting Brackets

with the included (6) 8mm x 25mm Hex Bolts, (6) 8mm Lock Washers, and (6) 8mm Flat

Passenger/Right

Front and Center

Mounting

Brackets

Drive/Left Front

and Center

Mounting

Brackets

(6) 12mm x 40mm Bolt x 10mm

Nut Plates

Passenger/

Right Rear

Mounting

Bracket

Driver/Left

Rear

Mounting

Bracket

Front

(6) 12mm Plastic Retainers

Passenger Sidebar Illustrated

1 2 3

Inhaltsverzeichnis

Seite 1 - Page 1 of 3 12/16/11 (DP)

5" OVAL BENT END SIDEBARS 09-12 DODGE RAM 1500 CREW CAB 10-12 DODGE RAM 25-3500 CREW CAB EXCLUDES VEHICLES EQUIPPED WITH DIESEL EXHAUST FLUID SYS

Seite 2

5" OVAL BENT END SIDEBARS 09-12 DODGE RAM 1500 CREW CAB 10-12 DODGE RAM 25-3500 CREW CAB EXCLUDES VEHICLES EQUIPPED WITH DIESEL EXHAUST FLUID SYS

Seite 3 - Page 3 of 3 12/16/11 (DP)

5" OVAL BENT END SIDEBARS 09-12 DODGE RAM 1500 CREW CAB 10-12 DODGE RAM 25-3500 CREW CAB EXCLUDES VEHICLES EQUIPPED WITH DIESEL EXHAUST FLUID SYS

Kommentare zu diesen Handbüchern

Keine Kommentare

Steelcraft-automotive 422509p 5 PREMIUM OVAL SIDE BAR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Steelcraft-automotive 422509p 5 PREMIUM OVAL SIDE BAR herunter. Steelcraft Automotive 422509p 5 PREMIUM OVAL SIDE BAR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Steelcraft-automotive 422509p 5 PREMIUM OVAL SIDE BAR