Steelcraft-automotive 72260 BULL BAR Bedienungsanleitung PDF herunterladen

BULL BAR

2010 DODGE RAM 25-3500

Page 1 of 2 3/9/10 (DP)

PARTS LIST:

Qty

Description

Qty

Description

Bull Bar

10mm x 27mm OD x 3mm Flat Washers

Driver/Left Frame Mounting Bracket

10mm Lock Washers

Passenger/Right Frame Mounting Bracket

10-1.5mm Hex Nuts

10-1.5mm x 35mm Hex Bolts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. TOW HOOKS CANNOT

BE REINSTALLED WITH THIS BULL BAR. NOTE: It may be necessary to remove/relocate front

license plate and license plate bracket. It is not required, but strongly recommended. If local/state

law requires a visible front license plate, a license plate relocation kit is available.

2. Starting at the front of the vehicle, determine if the truck is equipped with or without factory tow

hooks, (Figure 1).

For models without tow hooks:

Select the driver side Frame Bracket. Bolt the Bracket to the (2) outer holes in the frame with

the included (2) 10mm x 35mm Hex Bolts, (4) 10mm Flat Washers, (2) 10mm Lock Washers

and (2) 10mm Hex Nuts, (Figure 2 & 3). Snug the hardware but do not tighten at this time.

Repeat this step for passenger side Frame Mounting Bracket installation

For models with tow hooks:

Remove the (4) hex bolts holding the tow hook to the frame, (Figure 1). Remove the tow hook.

TIP: Removing the inner hex bolts securing each tow hook can be difficult to reach from behind

the bumper, (long socket extensions required). It may be easier to access the (2) hex bolts by

going through the front of the bumper opening and holding the hex nuts in place with an open-

ended wrench, (Figure 2).

Select the driver side Frame Mounting Bracket and bolt it to the (2) outer holes for the tow hook

with the factory hardware or the included (2) 10mm x 35mm Hex Bolts, (4) 10mm Flat Washers,

(2) 10mm Lock Washers and (2) 10mm Hex Nuts, (Figure 2 & 3). Snug the hardware but do not

tighten at this time. Repeat this step for passenger side Frame Mounting Bracket installation.

3. With help, position the Bull Bar up to the outside of the Mounting Brackets. Use the included (4)

10-1.5mm x 35mm Hex Bolts, (4) 10mm Lock Washers, (8) 10mm Flat Washers and (4) 10-

1.5mm Hex Nuts to attach the Bull Bar to the Mounting Brackets, (Figure 4). Snug but do not

tighten hardware.

Passenger/Right

Side Frame

Mounting

Bracket

Driver/Left Side

Frame Mounting

Bracket

Installation Complete

1 2

PARTS LIST: 1
Page 2 of 2 3/9/10 (DP) 2

Inhaltsverzeichnis

Seite 1 - PARTS LIST:

BULL BAR 2010 DODGE RAM 25-3500 Page 1 of 2 3/9/10 (DP) PARTS LIST: Qty Description Qty Description 1 Bull Bar 16 10mm x 27mm OD x 3mm Flat Was

Seite 2 - Page 2 of 2 3/9/10 (DP)

BULL BAR 2010 DODGE RAM 25-3500 Page 2 of 2 3/9/10 (DP) 4. Stand back from the vehicle and check to see that the Bull Bar is centered and level o

Kommentare zu diesen Handbüchern

Keine Kommentare

Steelcraft-automotive 72260 BULL BAR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Steelcraft-automotive 72260 BULL BAR herunter. Steelcraft Automotive 72260 BULL BAR User Manual [es] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Steelcraft-automotive 72260 BULL BAR