Steelcraft-automotive 70230 BULL BAR Bedienungsanleitung PDF herunterladen

3" BULL BAR

2014 CHEVY SILVERADO1500/GMC SIERRA1500

Page 1 of 3 7/10/13 (DP)

PARTS LIST:

Qty

Description

Qty

Description

Bull Bar

10-1.50mm x 30mm Hex Bolt

Driver/Left Mounting Bracket

10mm x 27mm OD x 3mm Flat Washer

Passenger/Right Mounting Bracket

10mm Lock Washer

10-1.50mm x 30mm Double Bolt Plates

10-1.50mm Hex Nut

10-1.50mm x 35mm Bolt Plates

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. CUTTING IS REQUIRED.

2. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not

required, but strongly recommended. If local/state law requires a license plate, a license plate

relocation kit is available.

3. Start installation from under the front of the vehicle. Determine if the vehicle is equipped with tow

hooks.

Tow Hook equipped vehicles:

a. Remove the steel bumper and brackets to access the hardware securing the tow hook to the

frame channel.

b. Remove the factory tow hook from the end of each frame channel, (Figure 1). NOTE: This Bull

Bar is not compatible with tow hooks.

c. Cut out the opening in the plastic bumper insert to clear the Mounting Brackets, (Figure 1).

d. Reinstall the bumper after tow hooks have been removed and the openings have been cut out

and checked for clearance.

Vehicles without tow hooks:

a. Cut out the indented area in both sides of the plastic bumper insert to clear the Brackets as

pictured, (Figures 1 & 2). IMPORTANT: Make several small cuts for best fit. Do not cut through

the top edge of the panel. NOTE: The plastic panel is held in place with several small screws

that are difficult to reach and remove. If you prefer to remove the panel to cut out the openings,

it may be necessary to remove the steel bumper to access all of the small screws and clips.

b. Reinstall the bumper once openings have been cut out and checked for clearance.

4. Select the driver side Mounting Bracket. Insert the Bracket through the opening in the plastic bumper,

(Figure 3). Line up the (3) holes in the Bracket with the holes in the end of the frame channel.

5. Select the 10mm Double Bolt Plate, (Figure 4A). Insert the Bolt Plate into the end of the frame channel,

through the holes in the Bracket and out the side of the frame. Secure the Bolt Plate to the Brackets

with (2) 10mm Flat Washers, (2) 10mm Lock Washers and (2) 10mm Hex Nuts, (Figure 4B). Leave

loose at this time. Repeat this Step to install the 10mm x 35mm Bolt Plate, (Figure 5A), into the

remaining hole in the side of the Bracket and frame channel, (Figure 5B).

Passenger/Right Frame

Mounting Bracket

Driver/Left Frame

Mounting Bracket

(2) 10mm x 35mm

Bolt Plates

(2) 10mm x 30mm

Double Bolt Plates

1 2 3

Inhaltsverzeichnis

Seite 1 - Page 1 of 3 7/10/13 (DP)

3" BULL BAR 2014 CHEVY SILVERADO1500/GMC SIERRA1500 Page 1 of 3 7/10/13 (DP) PARTS LIST: Qty Description Qty Description 1 Bull Bar 4 10

Seite 2

3" BULL BAR 2014 CHEVY SILVERADO1500/GMC SIERRA1500 Page 2 of 3 7/10/13 (DP) 6. Repeat Steps 4 & 5 to install the passenger side Mounting B

Seite 3 - 3" BULL BAR

3" BULL BAR 2014 CHEVY SILVERADO1500/GMC SIERRA1500 Page 3 of 3 7/10/13 (DP) Driver Side Installation Pictured

Kommentare zu diesen Handbüchern

Keine Kommentare

Steelcraft-automotive 70230 BULL BAR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Steelcraft-automotive 70230 BULL BAR herunter. Steelcraft Automotive 70230 BULL BAR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Steelcraft-automotive 70230 BULL BAR