Steelcraft-automotive 422509 5 OVAL SIDE BAR Bedienungsanleitung PDF herunterladen

5" OVAL STRAIGHT SIDEBARS

09-11 DODGE RAM 1500 CREW CAB

10-11 RAM 2500-3500 CREW CAB

Page 1 of 3 10/1/10 (DP)

PARTS LIST:

Qty

Description

Qty

Description

Driver/Left Sidebar

12mm Lock Washers

Passenger/Right Sidebar

12mm Hex Nuts

Driver/Left Front & Center Mounting Brackets

10-1.5mm x 35mm Hex Bolts

Passenger/Right Front & Center Mounting Brackets

10mm x 27mm OD x 3mm Flat Washers

Driver/Left Rear Mounting Bracket

10mm Lock Washers

Passenger/Right Rear Mounting Bracket

8-1.25 x 25mm Hex Bolts

12mm Plastic Retainers

8mm x 24mm x 2mm Flat Washers

12mm x 40mm Bolt x 10mm Nut Plates

8mm Lock Washers

12mm x 32mm OD x 3mm Flat Washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting at the driver side-front of the vehicle, remove the sealing tape covering the factory holes on the

side of the inner panel, (Figure 1A, 1B, 1C). Partially thread (1) 12mm Plastic Retainer onto the

threaded end of (1) 12mm Bolt and Nut Plate. Insert the Bolt and Nut Plate into the factory oval hole.

Continue to thread the Plastic Retainer down the Bolt and Nut Plate until it is flush against the sheet

metal, (Figure 2). NOTE: When properly installed, the Plastic Retainer is designed to prevent the Bolt

and Nut Plate from falling into the body cavity during installation.

3. Select the driver side front Mounting Bracket and partially hang it from the Bolt and Nut Plate with (1)

12mm Flat Washer, (1) 12mm Lock Washer and (1) 12mm Hex Nut. Do not tighten hardware at this

time. Line up the remaining hole in the Mounting Bracket with the hole in the inner body panel. Rotate

the Bolt and Nut Plate until the threaded end (Nut) lines up with the hole in the Mounting Bracket.

Secure with (1) 10mm x 35mm Hex Bolt, (1) 10mm Lock Washer and (1) 10mm Flat Washer, (Figure

3A, 3B, 3C). Snug but do not tighten hardware at this time.

4. Repeat the installation procedure in Steps 2-3 for all remaining Mounting Brackets. Use the illustration

on Page 1 to determine the correct Mounting Bracket for each of the remaining locations.

5. Once all of the brackets have been installed, with assistance, carefully position the driver Sidebar onto

the Mounting Brackets. Partially attach the Sidebar to the cradles on the Mounting Brackets using the

included (6) 8mm x 25mm Hex Bolts, (6) 8mm Lock Washers, and (6) 8mm Flat Washers, (Figure 4).

Do not tighten hardware at this time.

Passenger/Right

Rear Mounting

Bracket

Passenger/Right

Center Mounting

Bracket

Passenger/Right

Front Mounting

Bracket

Driver/Left Front

Mounting Bracket

Drive/Left Center

Mounting Bracket

Driver/Left Rear

Mounting Bracket

Sidebar pictured for example

only. Actual sidebar may differ

(6) 12mm x 40mm Bolt x 10mm

Nut Plates

Front

Rear

1 2 3

Inhaltsverzeichnis

Seite 1 - Page 1 of 3 10/1/10 (DP)

5" OVAL STRAIGHT SIDEBARS 09-11 DODGE RAM 1500 CREW CAB 10-11 RAM 2500-3500 CREW CAB Page 1 of 3 10/1/10 (DP) PARTS LIST: Qty Descripti

Seite 2

5" OVAL STRAIGHT SIDEBARS 09-11 DODGE RAM 1500 CREW CAB 10-11 RAM 2500-3500 CREW CAB Page 2 of 3 10/1/10 (DP) 6. Properly level and adjust the

Seite 3 - 10-11 RAM 2500-3500 CREW CAB

5" OVAL STRAIGHT SIDEBARS 09-11 DODGE RAM 1500 CREW CAB 10-11 RAM 2500-3500 CREW CAB Page 3 of 3 10/1/10 (DP) Driver Side Installation Pictured

Kommentare zu diesen Handbüchern

Keine Kommentare

Steelcraft-automotive 422509 5 OVAL SIDE BAR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Steelcraft-automotive 422509 5 OVAL SIDE BAR herunter. Steelcraft Automotive 422509 5 OVAL SIDE BAR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Steelcraft-automotive 422509 5 OVAL SIDE BAR