Steelcraft-automotive 51360 GRILL GUARD Bedienungsanleitung PDF herunterladen

GRILLE GUARD

2009-013 F-150

Page 1 of 7 1/31/13 Rev 5(DP)

PARTS LIST:

Grille Guard

12mm x 35mm Bolt Plates

Driver/Left Frame Mounting Bracket

12mm ID x 42mm x 42mm x 5.75mm Square

Washer

Passenger/Right Frame Mounting Bracket

3/8-16" x 1-1/4" Quick Release Bolts

Driver/Left Top Bracket

12mm Plastic Washers

Passenger/Right Top Bracket

3/8" x 1-1/4" Plastic Washers

Driver/Left Top Support Bracket

12-1.75mm x 35mm Hex Bolts

Passenger/Right Top Support Bracket

12mm x 32mm OD x 3mm Flat Washers

Driver/Left Top Support Brace

12mm Lock Washers

Passenger/Right Top Support Brace

12mm Hex Nuts

50mm x 75mm x 1.0mm Adhesive Foam Tape

3/8" x 1-1/4" OD Flat Washers

12mm Double Nut Plates

3/8-16" Nylon Lock Nuts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. CUTTING

MAY BE REQUIRED (VEHICLES WITHOUT TOW HOOKS). LICENSE PLATE MUST BE

RELOCATED ON VEHICLES EQUIPPED WITH ECOBOOST.

2. WARNING! This Grille Guard is designed to swivel forward by partially loosening the Top Bracket

Quick Release Bolts and the upper bolts on the Frame Mounting Brackets when the hood needs to be

opened for service. Make sure that all hardware is fully tightened after closing the hood. Read Page 7,

"Opening and closing of hood," before installing the Grille Guard. NOTE: It may be necessary to

remove/relocate the front license plate and license plate bracket. It is not required, but strongly

recommended. If local/state law requires a license plate, a license plate relocation kit is available.

3. Determine if the vehicle is or is not equipped with factory tow hooks.

Installation on vehicles without Tow Hooks:

a. On some vehicles, it may be necessary to remove the lower plastic portion of the bumper to

gain access to the ends of the frame rails, (Figure 1). An opening in the lower bumper cover will

need to be cut out, (if closed), to allow the Mounting Brackets to pass through. Do not trim the

Passenger/Right Frame

Mounting Bracket

(2) 12mm Double Nut Plates

Driver/Left Side Frame

Mounting Bracket

Driver/Left

Top Bracket

Passenger/Right

Top Bracket

Driver/Left

Top Support

Bracket

Passenger/

Right Top

Support

Bracket

(2) 12mm x 35mm Bolt Plates

(2) 3/8-16" x 1-1/4"

Quick Release Bolts

(1) 12mm ID x 40mm x 40mm x 5mm

Square Washer

Passenger/Right

Top Support Brace

Driver/Left Top

Support Brace

50mm x 75mm x 1.0mm

Adhesive Foam Tape

1 2 3 4 5 6 7

GRILLE GUARD 4
2009-013 F-150 4

Inhaltsverzeichnis

Seite 1

GRILLE GUARD 2009-013 F-150 Page 1 of 7 1/31/13 Rev 5(DP) PARTS LIST: 1 Grille Guard 2 12mm x 35mm Bolt Plates 1 Driver/Left Frame Mounting Brac

Seite 2

GRILLE GUARD 2009-013 F-150 Page 2 of 7 1/31/13 Rev 5(DP) plastic cover until after the Lower Mounting Brackets have been installed and properly ali

Seite 3

GRILLE GUARD 2009-013 F-150 Page 3 of 7 1/31/13 Rev 5(DP) a. On vehicles without tow hooks: Temporarily remove the Grille Guard. Hold the plastic l

Seite 4 - 2009-013 F-150

GRILLE GUARD 2009-013 F-150 Page 4 of 7 1/31/13 Rev 5(DP) Driver Side Installation Pictured (Fig 4)

Seite 5

GRILLE GUARD 2009-013 F-150 Page 5 of 7 1/31/13 Rev 5(DP) Driver Side Installation Pictured Fig 10 1

Seite 6

GRILLE GUARD 2009-013 F-150 Page 6 of 7 1/31/13 Rev 5(DP) Driver Side Installation Pictured Fig 13 F

Seite 7

GRILLE GUARD 2009-013 F-150 Page 7 of 7 1/31/13 Rev 5(DP) Driver Side Installation Pictured Opening and closing the

Kommentare zu diesen Handbüchern

Keine Kommentare

Steelcraft-automotive 51360 GRILL GUARD Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Steelcraft-automotive 51360 GRILL GUARD herunter. Steelcraft Automotive 51360 GRILL GUARD User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Steelcraft-automotive 51360 GRILL GUARD